ZBA ZB-8210 Bedienungsanleitung

ZB-8150/ZB-8110/ZB-8210CCD BARCODE SCANNERUser’s ManualZBA Inc 94 Old Camplain Road Hillsborough NJ 08844Phone: 908-359-2070 Fax: 908-359-1272

Keyboard wedge As a keyboard interface, the scanner supports most of the popular PCs and IBM terminals. The installation of the wedge is a fairly sim

Keyboard wedge Keyboard Layout: The selecting of keyboard layout supports many country languages other than USA keyboard layout. First you need to co

Keyboard layout USA Belgium Danish France Germany Italian Portuguese Spanish Swedish Switzerland UK Latin American 00＊ 01 02 03 04 05 06 07 08 09 10 1

Keyboard wedge Caps Lock: By selecting Caps Lock or No Caps Lock, scanner can get Caps Lock status. Power-on simulation: All of the PCs check the k

Program Option Bar Code Option Alphanumeric Entry Caps lock Caps lock”ON” Caps lock”OFF”00 01＊ Power-on simulationDisable Enable 00＊ 01 Inter-ch

RS-232 CTS: Clear To Send (Hardware Signal) RTS: Request To Send (Hardware Signal) Xon: Transmit On (ASCII Code 1116) Xoff: Transmit Off (ASCII Code

Program Option Bar Code Option Alphanumeric Entry Flow control None RTS/CTS Xon/Xoff ACK/NAK 00＊ 01 02 03 Inter-character delay00-99 (msec) 00-9

Program Option Bar Code Option Alphanumeric Entry Baud rate 300 BPS 600 BPS 1200 BPS 2400 BPS 4800 BPS 9600 BPS 19200 BPS 38400 BPS 00 01 02 03

Wand Emulation Bar/space polarity: High/low- Black will be transmitted as a high voltage level (+5) and space as low level (0V). Low/high- Black

Wand Emulation Output speed: This setting is same as serial transmission baud rate, and it must be approbated your wand decode resolution. The unit o

Installation:Keyboard Wedge 1) Turn off the PC2) Disconnect the keyboard cable from the PC. 3) Connect the Keyboard Cable to the scanner and connec

Reserved 00＊ Reserved 00＊ Margin delay 00-99 (10 pixel)00-99 15＊ Transmit delay 00-99 (10 msec)00-99 30＊ Exit 20

Scan Scanning mode: Good-read off-The trigger button must be pressed to activate scanning. The light source of scanner stops scanning when there i

Program Option Bar Code Option Alphanumeric Entry Scanning mode Good-read off Momentary Alternate Timeout off Continue 00 01＊ 02 03 04 Stand-

Scan Multi field scan: The scanner can be read many sets of barcode data on the same scanning line at the same time, even if they are different kinds

Multi field scan Disable Enable 00＊ 01 Global min. code length00-63 00-63 04＊ Global max.code length00-63 04-63 63＊ Inverted image scan Disable

Indication Power on alert: After power-on the scanner it will generate an alert signal to indicate a successful self-test. LED indication: After e

Program Option Bar Code Option Alphanumeric Entry Power on alert Disable Enable 00 01＊ LED indication Disable Enable 00 01＊ Buzzer indication

UPCA Read: Format Leading Zero Data Digits(11 Digits)Check Digit Check-sum transmission: By setting Enable, checks sum will be transmitted. Truncate

Check-sum verification Disable Enable 00 01＊ Check-sum transmissionDisable Enable 00 01＊ Max.code length 00-64 00-64 64＊ Min.code length 00-64 00-

UPCA Supplement digits: The Supplement digits barcode is the supplemental 2 or 5 characters for

Default Setting for each barcode shown as below: Read Enable Code Type 8110 8150/8210ChecksumVerification Enable ChecksumTransmissionEnable CodeIDUP

UPCE Read: Format Leading Zero Data Digits (6 Digits) Check Digits Check-sum verification: The checksum of EAN-13 is optional and made as the sum of

UPCE Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group selectio

Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < E >＊ Insert group selection 00-44 00-44 00＊ Supplement digits None

EAN-13 Read: Format Data Digits (12 Digits) Check Digits Check-sum verification: The checksum of EAN-13 is optional and made as the sum of the numeri

Check-sum verification Disable Enable 00 01＊ Check-sum transmission Disable Enable 00 01＊ Max.code length 00-64 00-64 64＊ Min.code length 00-64 00-6

EAN-13 Code Id setting: Refer to Code ID setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Supplement digits

Program Option Bar Code Option Alphanumeric Entry Code ID setting 00-ffH ASCII code 00-ffH < F >＊ Insert group selection 00-44 00-44 00＊

EAN-8 Read: Format Data Digits (7 Digits) Check Digits Check-sum verification: The checksum of EAN-8 is optional and made as the sum of the numerical

Check-sum transmission Disable Enable 00 01＊ Max.code length 00-64 00-64 64＊ Min.code length 00-64 00-64 01＊ Truncate leading 0-15 00-15 00＊ Trunca

EAN-8 Supplement digits: Format Data Digits(7 Digits)Check Digits Supplement Digits2 or 5 or UCC/EAN 128 Truncate Leading zero: Refer to Truncate Lea

ZBA ZB- 8110 / 8150 - 1D Barcode scannerSpecification Model 8110 Model 8150 Operational Light Source 660 nm Visible Red LED Optical System 2048 pi

Code 39 Read: Format Start“★” Data Digits( Variable)Checksum(Optional)End“★”Check-sum verification: The checksum of Code-39 is optional and made as

Code 39 Max./Min. code length: Each symbology has own Max./Min. Code Length. They can be set to qualify data entry. If their Max./Min. Code Length is

Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting

Code 39 Append: This function allows several symbols to be concatenates and be treat as one single data entry. The scanner will not transmit the embe

Interleaved 2 of 5 Read: Format Data Digits (Variable) Checksum (Optional) Check-sum verification: The checksum is made as the sum module 10 of the

Interleaved 2 of 5 Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UP

Code ID setting 00-ffH ASCII code 00-ffH < i >＊ Insert group selection 00-44 00-44 00＊ Exit 46

Industrial 2 of 5 Read: Format Data Digits (Variable) Checksum (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncat

Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < i >＊ Insert group selection 00-44

Matrix 2 of 5 Eur Read: Format Data Digits (Variable) Checksum (Optional) Checksum Verification: The checksum is made as the sum module 10 of the n

Weight 155 g (cable not included) 160 g (cable not included) Cable – K/B wedge Straight 2.0 m Cable – universal type Straight 2.3 m Connector type R

Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-

Codabar Read: Format Start Data Digits (Variable) Checksum (Optional) End Checksum Verification: The checksum is made as the sum module 16 of the nu

Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ T

Codabar Insertion group selection: Refer to Insertion group selection of UPCA. Start/End type: The Codabar has four pairs of Start/End pattern; you m

Code-128 Read: Format Data Digits (Variable) Checksum (Optional) Checksum Verification: The checksum is made as the sum module 103 of all data dig

Code-128 Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id

Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < # >＊ Insert group selection

Code-93 Read: Format Data Digits(Variable)Checksum1(Optional)Checksum2(Optional)Checksum Verification: The checksum is made as the sum module 47 of

Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00

Code-11 Read: Format Data Digits(Variable)Checksum1(Optional)Checksum2(Optional)Checksum Verification: The checksum is presented as the sum module

Programming Programming method Manual (Reading special barcode) DOS command through RS-232, Windows configuration program Program upgrade Enabled by

Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ T

MSI/plessey Read: Format Data Digits(Variable)Checksum1(Optional)Checksum2(Optional)Checksum Verification: The MSI/Plessey has one or two optional c

Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ T

UK/plessey Read: Format Data Digits (Variable) Checksum1+2(Optional) Checksum Verification: The UK/Plessey has one or two optional checksum digits.

Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ T

Telepen Read: IATA (International Air Transport Association). Checksum Verification: The checksum is presented as the sum module 10 or 11 of the data

Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setti

Standard 2 of 5 Read: Format Data Digits (Variable) Checksum1(Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncat

Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < i >＊ Insert group selection 00

RSS-14 Read: Format Data Digits (Variable) Checksum1(Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/e

Programming the 8110/8150/8210 To program the 8110/8150/8210, you must scan a series of programming barcode in the correct order. Fold out the back c

Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < R4 >＊ Insert group selection 0

RSS-Limited Read: Format Data Digits (Variable) Checksum1(Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate le

Min. code length 00-64 00-64 01＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH <

RSS-Expanded Read: Format Data Digits (Variable) Checksum1(Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate l

Min. code length 00-64 00-99 01＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH <

China Post Read: Format Data Digits (Variable) Checksum1(Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate lea

Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < t >＊ Insert group selec

Italian Pharmacode Read: Format Data Digits (Variable) Checksum1(Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Trun

Min. code length 00-64 00-64 09＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 0

Code-16K Only the ZB-8210 can decode Code-16K. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID se

Option Bar Code Option Alphanumeric Entry Interface selection Keyboard Wedge RS-232 Wand emulation USB Keyboard/RS-232 Auto detection reser

PDF-417 Only the ZB-8210 can decode PDF-417. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID sett

String setting Prefix characters: Up to 22 ASCII characters may be sent before data digits. Prefix Data Digits Suffix Suffix characters: Up to 22 ASCI

Preamble characters setting None 1-22 characters00＊ 00-ffH ASCII code Postamble characters setting None 1-22 characters00＊ 00-ffH ASCII code Insert G1

String setting Insert G1/G2/G3/G4 character setting: The scanner offer 4 positions and 4 characters to insert among the symbol. Example: Barcode “1 2

Insert G3 characters setting None 1-22 characters00＊ 00-ffH ASCII code Insert G4 characters setting None 1-22 characters00＊ 00-ffH ASCII code Exit

Transmission Preamble transmission: By setting Enable, Preamble will be appended before the data transmitted. Postamble transmission: By setting

Insert data group 1 position 00-64 (00: no insertion)00-64 00＊ Insert data group 2 position 00-64 (00: no insertion)00-64 00＊ Insert data group 3 pos

Transmission Code ID transmission: If your application is needed to transmit Code ID, you must set this to Proprietary ID or AIM ID. Code length tra

Code length transmission Disable Enable 00＊ 01 Code name transmission Disable Enable 00＊ 01 Case conversion Disable Upper case Lower case *For barcod

Test Chart CODABAR-PARA CODE-11 PARA CODE-128 PARA CODE-39 PARA CODE-93 PARA EAN-13 PARA 89

Interface Selection This decoder build-in scanner comes in one model and supports interfaces such as keyboard wedge, RS232 serial wedge, wand emulati

PDF-417 STANDRAD-25 PARA CODE-16K EAN-8 PARA INDUSTRIAL-25 PARA UPCE PARA 8754990

INTERLEAVED-25 PARA MATRIX 25 PARA MSI/PLESSEY PARA UPCA PARA UK/PLESSEY PARA 91

ASCII Code Table Note: For keyboard wedge only. L H 0 1 0 1 0 Null NUL DLE 1 Up F1 SOH DC1 2 Down F2 STX DC2 3 Left F3

Parameter Setting List Program Barcode standard parameter setting list If you wish to display the current configuration of your ZB-8110/8150/82

Firmware version list If you wish to display the firmware version, scan the Firmware version list. WARNING: Default value initialization If you

97 0A1B2C3D4E5F678Finish995